![]() Sometimes the motor may be running but there is something blocking its movement – this will prevent it from spinning properly. Next, look for any visible signs of wear and tear on the blades and ensure they are free from anything obstructing their rotation. Make sure that the switch is turned on and that the breaker has not been tripped by flipping off a nearby circuit breaker. The first thing you should do is check the power switch. If your harbor breeze ceiling fan not working but the light works. When it stops working, it can cause a lot of problems. Make sure all the colored cables are in their proper places, and that the plug connection in the switch housing is firmly fastenedĪlso Read: How To Fix Harbor Breeze Ceiling Fan Light Not Working? ConclusionĪ ceiling fan is an important thing to have in your home or office.Verify that the reverse switch is not set to neutral.Ensure that the fan blades can freely rotate.Bypass the circuit breaker to cut off the power.To make sure that the power is on, check the circuit breaker.How to fix a ceiling fan that won’t turn on? Slide out the old receiver and replace it with the new one be sure to put back in two retaining screws on top of the new receiver FAQ’s.Unplug the wires connected to the receiver and remove two retaining screws from top of the receiver.Remove three screws from the bottom of the base housing with a screwdriver to expose the remote control receiver.Turn off power to the ceiling fan at the breaker box (electricity).This is a simple fix, and should only take about 10 minutes. It’s likely that either the remote control receiver or the battery has gone bad. If your Harbor Breeze ceiling fan is not working but the light works. Replace The Remote Control Receiver And/or Batteries Otherwise, contact an electrician to get it replaced. It’s possible for the remote to stop working, in which case you can replace it yourself if you have experience in dealing with wiring like this. The remote control unit is the part of the fan that gets installed by a professional electrician and it controls the speed and direction of the blades. If you still experience problems with your ceiling fan after completing these steps, contact a professional for assistance. Double-Check All ConnectionsĬheck that the power cord is firmly plugged into the outlet and that the ceiling fan is not in a position where it could be blocked from receiving power.Ĭheck that all of the connections are tight, and make sure there are no bent or broken blades. If you find one, tighten it as best you can with a Phillips head screwdriver and see if the ceiling fan starts working again. ![]() Check for any screws that are not completely tight. If you’ve made it through the steps above and your ceiling fan is still not working, then you may have a loose screw. Once you have removed all of these, use a screwdriver or other tool to gently pry off each blade from its slot. Next, take out all of the screws on the blade arms. First, you’ll need to remove the light kit and fan cover by unscrewing all of the screws that hold it in place. This step is a little more difficult because you’ll need to access the blades. It is preferable to call an electrician if the motor is not running. Otherwise, there may be an issue with the wiring or a faulty switch. If it’s running but the fan blades are not moving, this is a problem with the remote or the receiver. In the case, you’ve exhausted your troubleshooting efforts and you’re still not getting a response from your ceiling fan, listen for the motor. If your wires are not loose, then your motor is most likely dead. You will need to locate where it may be and tighten it up. If there is no flickering or change in the operation of the fan, then you have a loose wire somewhere. You can do this by flipping the switch on and off. ![]() If the light works but the fan doesn’t, you should check if any of the wires are broken. If you’re sure that everything is turned on and working, then move on to the next step. If your light is on but the fan isn’t spinning, then make sure that your breaker hasn’t tripped or blown out. Most harbor breeze Ceiling fans have a light and a switch for the fan. Conclusion Check Whether The Power Is Onįirst, check the power to your ceiling fan.How to fix a ceiling fan that won’t turn on?.Why is the Harbor Breeze ceiling fan remote not working?. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |